ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX
16 January 2010, 11:20 AM | #1 |
"TRF" Member
Join Date: Dec 2009
Real Name: Jeff
Location: Morgantown, WV
Watch: Deep Sea
Posts: 55
|
Bracelet link removal
Hi all,
I just got a 116713 and need to remove a link for proper fit. I have a set of tiny screwdrivers but was unable to get the screw started, and it began to bugger up the screw, so i stopped. took it to a local jeweler today which has a watchmaker i have used for pin replacements and asked him to remove the link for me. he couldnt get the screw to budge, either. what are my options aside from sending it to the RSC for a simple link removal? all suggestions appreciated, thanks, jeff |
16 January 2010, 11:26 AM | #2 |
TRF Moderator & 2024 SUBMARINER Patron
Join Date: May 2007
Real Name: Larry
Location: Mojave Desert
Watch: GMT's
Posts: 43,401
|
Well, gee....there are 4 other links to try.....
They should not be very tight, but they will be loctited in place and heat (such as a hairdryer) is the release agent for loctite......... (it takes a 1.6mm screwdriver) A good watchmaker will have the correct tool for stubborn screws..... If the one you tried doesn't have the tool, perhaps he isn't quite good enough...
__________________
(Chill ... It's just a watch Forum.....) NAWCC Member |
16 January 2010, 11:26 AM | #3 |
"TRF" Member
Join Date: Jan 2010
Real Name: Alan
Location: Wet coast, Canada
Watch: A few, yes
Posts: 368
|
A very large hammer and cold chisel should do the trick
Actually you might want to try a little heat to loosen the Loc-tite before trying agin with a correctly fitting screwdriver. A heat gun on low should do the trick, but for heavens sake don't over do it on the heat, you may want to wrap the rest of the band and watch in a damp towel. Of course if the threads on the pin or in the link are striped or galled you're going to be in a world of hurt. Good luck
__________________
Experience is something you don't get until just after you need it. - Steven Wright |
16 January 2010, 11:28 AM | #4 | |
"TRF" Member
Join Date: Jan 2010
Real Name: Alan
Location: Wet coast, Canada
Watch: A few, yes
Posts: 368
|
Quote:
__________________
Experience is something you don't get until just after you need it. - Steven Wright |
|
16 January 2010, 11:30 AM | #5 |
Member
Join Date: Apr 2009
Location: SoCal OC U.S.A.
Posts: 342
|
Try applying heat from a hair dryer to the link and screw. It will soften the loc-tite if that is the problem.
Mark |
16 January 2010, 11:41 AM | #6 |
"TRF" Member
Join Date: Dec 2009
Real Name: Jeff
Location: Morgantown, WV
Watch: Deep Sea
Posts: 55
|
thanks, i will give the heat a try
|
16 January 2010, 12:34 PM | #7 |
"TRF" Member
Join Date: Dec 2009
Real Name: Jeff
Location: Morgantown, WV
Watch: Deep Sea
Posts: 55
|
heat worked great, thanks for the tips.
when reinstalling the screw, should i use some additional loc-tite or another thread sealant, or dont worry about it? |
16 January 2010, 01:43 PM | #8 |
TRF Moderator & 2024 SUBMARINER Patron
Join Date: May 2007
Real Name: Larry
Location: Mojave Desert
Watch: GMT's
Posts: 43,401
|
If you don't have the correct grade of thread locker (such as loctite 221), it is best to not use any at all.. If it's the wrong grade you could find yourself having to drill out the stud and rethreading.... or tossing the link...
__________________
(Chill ... It's just a watch Forum.....) NAWCC Member |
16 January 2010, 02:07 PM | #9 |
"TRF" Member
Join Date: Dec 2007
Location: Virginia, USA
Posts: 593
|
Try tapping the screw just a little bit with a small hammer before unscrewing. Should slightly break the Loctite bond just enough to turn the screw easier.
|
16 January 2010, 02:21 PM | #10 |
"TRF" Member
Join Date: Nov 2008
Location: in my house...
Posts: 5,524
|
I always learn something new.. Good to know..
__________________
Cheers, Eduardo Be a WIS not a WUSS... and remove all the stickers.. |
16 January 2010, 03:56 PM | #11 |
"TRF" Member
Join Date: Dec 2009
Real Name: Jeff
Location: Morgantown, WV
Watch: Deep Sea
Posts: 55
|
thanks larry, i think i will use none since the only thread sealant i have i just used to install the drain on a clawfoot tub. best not to use that on the rolex i think...
|
16 January 2010, 04:44 PM | #12 |
"TRF" Member
Join Date: Jan 2010
Real Name: Alan
Location: Wet coast, Canada
Watch: A few, yes
Posts: 368
|
Glad to hear it worked for you
__________________
Experience is something you don't get until just after you need it. - Steven Wright |
16 January 2010, 04:49 PM | #13 | |
2024 ROLEX SUBMARINER 41 Pledge Member
Join Date: Nov 2006
Real Name: Eddie
Location: Australia
Watch: A few.
Posts: 37,344
|
Quote:
IMO, there is not a snowballs that tapping that little screw with a small hammer will do anything but stuff it completely. Please DO NOT DO THAT. |
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
*Banners
Of The Month*
This space is provided to horological resources.