The Rolex Forums   The Rolex Watch

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX


Go Back   Rolex Forums - Rolex Forum > Rolex & Tudor Watch Topics > Rolex WatchTech

Reply
 
Thread Tools Display Modes
Old 23 June 2017, 02:30 PM   #1
Blnrwearer
"TRF" Member
 
Join Date: Jun 2015
Location: California, USA
Posts: 65
Icon5 Experts: Does this look normal?

I tested my BLNR on timegrapher and at 12 up (crown right) position, it shows pretty "noisy" lines (see dots in lower half). Other positions look ok.

Looks like there are some touches? BTW, amplitude is a little low probably because it has been sitting there for 24 hours.

What do you think? Should I worry or send in for warranty?





Thanks in advance.
Blnrwearer is offline   Reply With Quote
Old 23 June 2017, 06:19 PM   #2
Vanessa CW21
TechXpert & 2016 Patron
 
Vanessa CW21's Avatar
 
Join Date: Aug 2007
Location: Mx
Posts: 1,572
The reading looks fine for a not-fully-wound watch. The crown-right position is never measured to begin with, so if anything, put it in the crown-left position. The "side noise" you see is probably because the watch is cased up.
Next time wind the watch 40 times to get an accurate reading.


Sent from my SM-G930T1 using Tapatalk
__________________
Member# 5731
Instagram: @vanessa.cw21

Watch my Rolex repair video: https://youtu.be/jDnaotCTpTA
Vanessa CW21 is offline   Reply With Quote
Old 24 June 2017, 02:54 AM   #3
Blnrwearer
"TRF" Member
 
Join Date: Jun 2015
Location: California, USA
Posts: 65
Thanks, Vanessa.

The following are the readings after fully wound. Crown right (12 up) is still pretty noisy. Crown left is similar. From what I understand, there is 1 dot for each tick and tock. Sounds like the upper line of dots (I don't know upper line indicates tick or tock) are very unstable for this position. Other positions are much better as indicated in pictures.





Blnrwearer is offline   Reply With Quote
Old 24 June 2017, 04:49 AM   #4
Vanessa CW21
TechXpert & 2016 Patron
 
Vanessa CW21's Avatar
 
Join Date: Aug 2007
Location: Mx
Posts: 1,572
The 0.3ms is the largest best error (crown up) and that's way within limits. Rolex allows up to 0.8ms max.

Sent from my SM-G930T1 using Tapatalk
__________________
Member# 5731
Instagram: @vanessa.cw21

Watch my Rolex repair video: https://youtu.be/jDnaotCTpTA
Vanessa CW21 is offline   Reply With Quote
Old 24 June 2017, 04:52 AM   #5
Vanessa CW21
TechXpert & 2016 Patron
 
Vanessa CW21's Avatar
 
Join Date: Aug 2007
Location: Mx
Posts: 1,572
Your amplitude is fantastic, btw. The side noise is nothing to worry about. It's very minimum.

Sent from my SM-G930T1 using Tapatalk
__________________
Member# 5731
Instagram: @vanessa.cw21

Watch my Rolex repair video: https://youtu.be/jDnaotCTpTA
Vanessa CW21 is offline   Reply With Quote
Old 24 June 2017, 08:03 AM   #6
Blnrwearer
"TRF" Member
 
Join Date: Jun 2015
Location: California, USA
Posts: 65
Thanks Vanessa,

I was a little concerned whether these erratic dots indicate something on escapement system or escape wheel...
Blnrwearer is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Asset Appeal

Wrist Aficionado

DavidSW Watches

Takuya Watches

OCWatches


*Banners Of The Month*
This space is provided to horological resources.





Copyright ©2004-2024, The Rolex Forums. All Rights Reserved.

ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

Rolex is a registered trademark of ROLEX USA. The Rolex Forums is not affiliated with ROLEX USA in any way.