ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX

TheDude · 15 March 2011, 11:39 AM

My 16660 had stopped running a month or so ago. I could not get it to start and the winding seemed odd.

I missed wearing it, so even though I knew it wasn't working I wound it up, set it, and put it on. To my surprise, it started running and has been going for 3 hours accurately.

What kinds of issues might have caused it to exhibit this type of behavior?

Rikki · 15 March 2011, 12:05 PM

Loose screw from the auto bridge probably came out floated into the balance stopped the watch then you josled it then came out and it started. IMO Rik Have it looked at

TheDude · 15 March 2011, 12:37 PM

Quote:

Originally Posted by Rikki

Loose screw from the auto bridge probably came out floated into the balance stopped the watch then you josled it then came out and it started. IMO Rik Have it looked at

So there could be a screw roaming free inside?

crhfish · 15 March 2011, 12:43 PM

Ditto,

I opened mine up the other day to clean it. One I had just purchased and one of the screws had come out of the auto bridge. It was not in the balance, yet, but it was just a matter of time. Get it looked at quick.

TheDude · 15 March 2011, 10:58 PM

Okay. It stopped overnight. I reset it this AM and tried to wind it. There was a hard detent upon the initial crown rotation with a sort of a snap/pop as the crown got past it.

Useful clue??

Also, where can I take it in the DC area??

MonBK · 15 March 2011, 11:00 PM

The clue is, hack the watch and bring it in for service.

TheDude · 15 March 2011, 11:07 PM

Quote:

Originally Posted by MonBK

The clue is, hack the watch and bring it in for service.

Okay. I was just going to ask if hacking was the appropriate next step. Thanks for that.

Any ideas on places local to me? Wash DC area?

MonBK · 15 March 2011, 11:12 PM

Quote:

Originally Posted by TheDude

Okay. I was just going to ask if hacking was the appropriate next step. Thanks for that.

Any ideas on places local to me? Wash DC area?

Dude, you have a screw loose and hacking is the correct way.

I always wanted to say that.

STEELINOX · 15 March 2011, 11:30 PM

Quote:

Originally Posted by MonBK

Dude, you have a screw loose and hacking is the correct way.

I always wanted to say that.

TheDude · 16 March 2011, 01:59 AM

Nevermind my request for a service location. The watch is already out for service.

TheDude · 17 March 2011, 02:48 AM

Good news - local certified Rolex guy says no loose or missing screws or other parts.

Just a watch in dire need of lubrication and cleaning. I'm having him do a service on it.

TheDude · 24 March 2011, 10:47 PM

Got the watch back a couple of days ago. Ultrasonic cleaning, reassembly, etc...

Watchmaker found the problem, he said one wheel was "frozen", and the pivot had developed a "scouring" on the pivot which stopped the whole watch. Clearly due to long-term operation in a bone-dry state.

Watch is running great now!

MonBK · 24 March 2011, 10:54 PM

Great, now show a picture of your "brand new" watch.

TheDude · 25 March 2011, 03:29 AM

Quote:

Originally Posted by MonBK

Great, now show a picture of your "brand new" watch.

It doesn't look a whole lot different. I didn't want it polished, so really it's basically the same. The insides probably look a whole lot better though...

15 March 2011, 11:39 AM	#1
TheDude "TRF" Member Join Date: Oct 2007 Location: DC Area, USA Watch: IIc,1680 Red,16660 Posts: 4,492	16660 started running again... My 16660 had stopped running a month or so ago. I could not get it to start and the winding seemed odd. I missed wearing it, so even though I knew it wasn't working I wound it up, set it, and put it on. To my surprise, it started running and has been going for 3 hours accurately. What kinds of issues might have caused it to exhibit this type of behavior?

15 March 2011, 12:05 PM	#2
Rikki TechXpert Join Date: Jun 2009 Real Name: Rik Dietel Location: Seminole Fla Watch: 5512 s/s Sub Posts: 1,818	Loose screw from the auto bridge probably came out floated into the balance stopped the watch then you josled it then came out and it started. IMO Rik Have it looked at __________________ Century 21 Certified watchmaker Omega Service Provider Trained Omega OWME Certified. Rolex Parts Account Holder.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

15 March 2011, 12:43 PM	#4
crhfish Member Join Date: Dec 2010 Location: Texas Posts: 159	Ditto, I opened mine up the other day to clean it. One I had just purchased and one of the screws had come out of the auto bridge. It was not in the balance, yet, but it was just a matter of time. Get it looked at quick.

15 March 2011, 10:58 PM	#5
TheDude "TRF" Member Join Date: Oct 2007 Location: DC Area, USA Watch: IIc,1680 Red,16660 Posts: 4,492	Okay. It stopped overnight. I reset it this AM and tried to wind it. There was a hard detent upon the initial crown rotation with a sort of a snap/pop as the crown got past it. Useful clue?? Also, where can I take it in the DC area??

15 March 2011, 11:00 PM	#6
MonBK Banned Join Date: Nov 2010 Location: Kingstown Posts: 58,279	The clue is, hack the watch and bring it in for service.

16 March 2011, 01:59 AM	#10
TheDude "TRF" Member Join Date: Oct 2007 Location: DC Area, USA Watch: IIc,1680 Red,16660 Posts: 4,492	Nevermind my request for a service location. The watch is already out for service.

17 March 2011, 02:48 AM	#11
TheDude "TRF" Member Join Date: Oct 2007 Location: DC Area, USA Watch: IIc,1680 Red,16660 Posts: 4,492	Good news - local certified Rolex guy says no loose or missing screws or other parts. Just a watch in dire need of lubrication and cleaning. I'm having him do a service on it.

24 March 2011, 10:47 PM	#12
TheDude "TRF" Member Join Date: Oct 2007 Location: DC Area, USA Watch: IIc,1680 Red,16660 Posts: 4,492	Got the watch back a couple of days ago. Ultrasonic cleaning, reassembly, etc... Watchmaker found the problem, he said one wheel was "frozen", and the pivot had developed a "scouring" on the pivot which stopped the whole watch. Clearly due to long-term operation in a bone-dry state. Watch is running great now!

24 March 2011, 10:54 PM	#13
MonBK Banned Join Date: Nov 2010 Location: Kingstown Posts: 58,279	Great, now show a picture of your "brand new" watch.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)