ROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEXROLEX
14 January 2010, 12:16 PM | #1 |
"TRF" Member
Join Date: Nov 2009
Location: Washington
Watch: rolex
Posts: 6
|
Daytona running slow
I have a Daytona 116523 that is running 60 seconds a day slow. The Dealer suggested I do the following before sending it back to him for repair. I am not concerned with getting this problem resolved, I just have never heard of this problem and the suggested procedure for me to try. Anyone have any information?
"It sounds like a hairspring entanglement. Let the watch run down until it stops. Then give it a tap the back with your index & middle finger as if a doctor is testing for a vein. Set the watch then wind it 35-40 times. This should do it. " |
14 January 2010, 02:09 PM | #2 |
TRF Moderator & 2024 SUBMARINER Patron
Join Date: May 2007
Real Name: Larry
Location: Mojave Desert
Watch: GMT's
Posts: 43,414
|
A tangled hairspring would cause your watch to run very fast........
60 seconds a day slow is unacceptable, and I would suspect that this is not an Authorized Dealer who would say such a thing.... However, provided the watch is genuine, I would not do any business with this Dealer and have my watch corrected elsewhere.. If it is from an AD, you have a warranty and can send it to Rolex yourself - directly..
__________________
(Chill ... It's just a watch Forum.....) NAWCC Member Last edited by Tools; 15 January 2010 at 01:51 PM.. |
15 January 2010, 12:30 AM | #3 |
"TRF" Member
Join Date: Nov 2009
Location: Washington
Watch: rolex
Posts: 6
|
Thanks,
The watch was purchased from a non-AD brick and mortar store on the east coast and I am on the west coast. The watch is genuine (back removed). The dealer asked me try this method before sending it back to him at his expense. I had never heard of hairspring entanglement and thumping the back before and I was curious if anyone else had heard of this repair method. BTW my local AD wanted $100 to bring the watch in for me to look at and no discount plus almost 10% tax. |
15 January 2010, 12:57 AM | #4 | |
"TRF" Life Patron
Join Date: Jun 2005
Real Name: Peter
Location: Llanfairpwllgwyng
Watch: ing you.
Posts: 52,887
|
Quote:
__________________
ICom Pro3 All posts are my own opinion and my opinion only. "The clock of life is wound but once, and no man has the power to tell just when the hands will stop. Now is the only time you actually own the time, Place no faith in time, for the clock may soon be still for ever." Good Judgement comes from experience,experience comes from Bad Judgement,.Buy quality, cry once; buy cheap, cry again and again. www.mc0yad.club Second in command CEO and left handed watch winder |
|
15 January 2010, 02:29 AM | #5 |
TechXpert
Join Date: Jun 2009
Real Name: Rik Dietel
Location: Seminole Fla
Watch: 5512 s/s Sub
Posts: 1,818
|
It shouldn't be a hairspring problem as Tools said but possibly a cap jewel got knocked out of place causing the balance to stop at times in certain positions without your knowledge. Best get it to a professional and have it looked at. The hairspring problem is called overcoiling and can happen after a sudden sharp jarring or hit and sometimes it will come undone by itself but usually it doesn't. Overcoiling will always cause a watch to go faster because you're shortening the arc of the balance wheel in half for 290 degrees of amplitude to in some cases less than 130 degrees. Hope that helps Rikki
|
15 January 2010, 01:18 PM | #6 |
"TRF" Member
Join Date: Nov 2009
Location: Washington
Watch: rolex
Posts: 6
|
I tested the time over 7 days using the US Time website. Every day it lost over 60 seconds a day. It didn't seem to matter whether it was on my wrist or on the winder. I have several other Rolexes and they are within COSC specs.
Again thanks for the help. The best part of this forum is I learn something everyday. |
15 January 2010, 01:58 PM | #7 |
TRF Moderator & 2024 SUBMARINER Patron
Join Date: May 2007
Real Name: Larry
Location: Mojave Desert
Watch: GMT's
Posts: 43,414
|
I can't say I care much for your AD's demands...
If you are in the Seattle area, the Ben Bridge chain works closely with a Rolex Training and Service school in the Bellevue area.. There is also a great watch shop that is an Omega Service Center, but also works on Rolex - Nesbit's Fine Watch Service... Any of those should be able to regulate your Daytona at a reasonable cost...and let you know if there is any other damage..
__________________
(Chill ... It's just a watch Forum.....) NAWCC Member |
16 January 2010, 08:05 AM | #8 |
TechXpert
Join Date: Mar 2007
Location: Rolex world
Watch: SS/W Skydweller
Posts: 527
|
Do you run the chronograph all of the time? Do you use the chronograph hand as a centre seconds hand?
There is a friction spring under the chronograph wheel to ensure the hand glides smoothly around the dial. If you run the chronograph constantly, this spring will wear and cause very poor timekeeping and reduced power reserve. A cap jewel dislodged could also cause the problem. If it is the friction spring, a partial strip down at least (maybe even a service) would be required, if it is a cap jewel it could be corrected quickly by a competent watchmaker. You need to get it checked by a professional. |
16 January 2010, 01:53 PM | #9 |
"TRF" Member
Join Date: Nov 2009
Location: Washington
Watch: rolex
Posts: 6
|
I'm in Olympia.
No I don't run the chronograph as a second hand. I agree that Ben Bridge has good repair people. I have bought from them in the past when they would discount. On the Daytona they wouldn't. The non-AD dealer was willing to discount. When I noticed the problem, I talked to the service manager and he suggested that I try "Thump Repair" first. They are willing to repair at no cost to me. It was something I had questions on so I asked the forum for their comments. The watch has not run down yet, but I will try their suggestion then send it back to them. It's not like I don't have another Rolex to wear. I don't expect this method will work and I don't expect to have any problem getting it repaired. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
*Banners
Of The Month*
This space is provided to horological resources.