I need to buy a replacement pin...

[Bigsykedaddy]

Hey guys it pangs me to have to write this post but if anyone would be able to give me a straight answer it would be you guys (Thanks a lot Google!)

After finally finding the correct fit for my new 114060 I ordered some loctite to put on the pins (since I had changed configurations 100 times trying to get the right fit.) I was happy to finally put some loctite on the pins and leave it be.

Well the glide lock link that connects to the half link was acting up when I was making micro adjustments throughout the day, almost like the link wasn't bending like the pin was stuck. I figured I must have gotten a little too much loctite on the pin and it would be a simple fix. I unscrewed the pin (which was harder than it should have been, lessons learned) and when it got to then end I couldn't get it out of the link. I got some needle nose pliers and used my shirt so I wouldn't scratch anything. I got it out and cleaned off the residue screwed the pin back in but when I tried to clip in the glide lock it was getting stuck and not locking in place.

upon further inspection I had pinched the end of the pin so it was sticking up some. It was hard to get back out with the screwdriver since now the screwdriver wouldn't completely fit seeing as it was pinched. I managed to get the pin out and I used a razor blade to pry the end open so I could screw it back into place and actually wear the watch.

It is working now but I need to order a replacement pin (the odd sized one that connects glide lock to the bracelet.) Should I contact my AD (Didn't buy the watch from him) or should I contact RSC and see if I can order one from them? I checked online (Ebay, google etc) and couldn't find that specific pin.

Sorry for the long winded post I just wanted to describe in detail what happened so someone knew exactly which link I was talking about.

Thank you all very much in advance you're life savers! Me right now -->


TLDR: I bent the end of the little pin that connects glide lock to the rest of the bracelet. Where can I order another one?

[Rocket_Man]

When you say "pin" do you mean the screws that connect the links? Or do you mean the spring bars? I'd ask an AD since these screws vary by model.

Did you use purple locktite? That should be removable, but if it is hard a little heat from a lighter or even hair dryer can help loosen it up.

[Bigsykedaddy]

Originally Posted by Rocket_Man

When you say "pin" do you mean the screws that connect the links? Or do you mean the spring bars? I'd ask an AD since these screws vary by model.

Did you use purple locktite? That should be removable, but if it is hard a little heat from a lighter or even hair dryer can help loosen it up.

Yeah I mean the screws that connect the links sorry. I did use the correct loctite but I think maybe some of it dripped down onto the screw body that's why it was sticking. I could unscrew it I just couldn't grab it and pull it out once it was unscrewed that's why I had to get out the needle nose pliers. Thank you I'll contact my AD I appreciate it. I would just use an extra screw that came with one of the extra links but this screw is shorter than all the others.

[Rocket_Man]

Originally Posted by Bigsykedaddy

Yeah I mean the screws that connect the links sorry. I did use the correct loctite but I think maybe some of it dripped down onto the screw body that's why it was sticking. I could unscrew it I just couldn't grab it and pull it out once it was unscrewed that's why I had to get out the needle nose pliers. Thank you I'll contact my AD I appreciate it. I would just use an extra screw that came with one of the extra links but this screw is shorter than all the others.

I've had to use small pliers too. I make sure to mask off the edges of the links so I don't scratch them up.

Another option would be one of the certified watchmakers on here with a Rolex parts account. They'd need the partnumber for the bracelet and as you've seen not all the screws are the same.

[Bigsykedaddy]

Originally Posted by Rocket_Man

I've had to use small pliers too. I make sure to mask off the edges of the links so I don't scratch them up.

Another option would be one of the certified watchmakers on here with a Rolex parts account. They'd need the partnumber for the bracelet and as you've seen not all the screws are the same.

Oh cool, I'll have to google and find one in my area, I assume they would be a bit cheaper than going through an AD. Do you happen to know if you can order just the screw by itself or are they going to make me buy an entire link?

Thanks again for the response

[mtgjr]

I told you not to use loctite...

[azguy]

People always use to much loctite you only need one super small dot or two and that's it

[watchwatcher]

Yeah...loctite can be tricky and you have to know what you're doing.

If you have a good relationship with your AD, I'm sure they could get you what you need, or barring that, one of the great watchmakers on this forum. Try posting this in the tech section and see if you get a response from one of them.

[RichM]

If it's the screw that connects the links, try your nearest AD. If they don't have one, they could order you a pack. They come in packs of five. I paid $25 for the pack. My AD had every one but the one I needed.

They did need the watch serial number to order the screws. Bring the watch and the card, just in case they have to order them.

[WAK4]

I'd go to the AD. They may charge you, but I can't imagine it'd be too much. Probably the easiest route. May even have it in inventory already.

Yeah, loctite can be tricky, one of the lessons I learned was to put a drop directly into the end piece, and not on the screw itself. While sliding the screw back into place, loctite gets into the link itself and makes it not rotate. Sounds like what happened to you, and I learned that the hard way myself...but fortunately no broken screws on my end.

[subtona]

proper loctite (221 or 222) on the threads and a proper hollow ground screwdriver should not result in a problem.

the only problem i see is the pliers to the screw head.

get a new pin and continue to use loctite (221 or 222)

[Etschell]

you say your 114060 is new, if that is the case how can you not have some extra pins in the links you arent using?

judging from your avatar you dont have anything more than a 7 inch wrist.

[padi56]

Originally Posted by WAK4

I'd go to the AD. They may charge you, but I can't imagine it'd be too much. Probably the easiest route. May even have it in inventory already.

Yeah, loctite can be tricky, one of the lessons I learned was to put a drop directly into the end piece, and not on the screw itself. While sliding the screw back into place, loctite gets into the link itself and makes it not rotate. Sounds like what happened to you, and I learned that the hard way myself...but fortunately no broken screws on my end.

Always put a very very tiny drop of loctite on the female part of the thread only.

[Bigsykedaddy]

Originally Posted by Rich Mickol

If it's the screw that connects the links, try your nearest AD. If they don't have one, they could order you a pack. They come in packs of five. I paid $25 for the pack. My AD had every one but the one I needed.

They did need the watch serial number to order the screws. Bring the watch and the card, just in case they have to order them.

This screw is not like the others it's the smaller one that connects glide lock to the rest of the bracelet, do you think those will be in house or will come in a pack of five? Thank you again.

Originally Posted by azguy

People always use to much loctite you only need one super small dot or two and that's it

Guys I did use a small amount of loctite, every other single link is perfectly fine. It was just a mistake that I must have missed. I wanted to use just a tad of loctite on every link (because over the course of a few weeks I had move them all around) just so I wouldn't have to worry about a screw backing out.

Originally Posted by subtona

proper loctite (221 or 222) on the threads and a proper hollow ground screwdriver should not result in a problem.

the only problem i see is the pliers to the screw head.

get a new pin and continue to use loctite (221 or 222)

I used a proper screw driver and the proper loctite. Every single link was fine but one, I made ONE mistake it happens. It unscrewed but just wouldn't come out, it's no big deal I was just wondering where I could source that specific screw since I've never had to order a part before.

Originally Posted by WAK4

I'd go to the AD. They may charge you, but I can't imagine it'd be too much. Probably the easiest route. May even have it in inventory already.

Yeah, loctite can be tricky, one of the lessons I learned was to put a drop directly into the end piece, and not on the screw itself. While sliding the screw back into place, loctite gets into the link itself and makes it not rotate. Sounds like what happened to you, and I learned that the hard way myself...but fortunately no broken screws on my end.

Awesome advice thank you very much.

Originally Posted by Etschell

you say your 114060 is new, if that is the case how can you not have some extra pins in the links you arent using?

judging from your avatar you dont have anything more than a 7 inch wrist.

Yeah you can see in the post that it's the link that connects glidelock to the bracelet so the screw is smaller than all the other ones. I have a 7'5'' wrist so I do have an extra link but the screw is the wrong size. If it was a normal link I wouldn't have asked the question because I know where to get those. Thank you for your response I appreciate it.

Originally Posted by padi56

Always put a very very tiny drop of loctite on the female part of the thread only.

Thank you very much that makes total sense, I appreciate it.

[dysondiver]

i cant help but wonder if the screw backing out is a tight bracelet thing , i wear mine loose , never bother with loctite , and have never had pin problems at all ,,
but , use the proper 221 or 222 ,,, thats the secret [ ive used nail varnish in the past though]

[cdmorenot]

Hey man. You're talking about the screw that does not show up on the other side of the link right?

In other words the end tip is hidden... Yeah, that one I managed to mangle a couple of times myself. Go to the AD and get it from them. The screw is $8 and they may have to order it.

[Bigsykedaddy]

Originally Posted by dysondiver

i cant help but wonder if the screw backing out is a tight bracelet thing , i wear mine loose , never bother with loctite , and have never had pin problems at all ,,
but , use the proper 221 or 222 ,,, thats the secret [ ive used nail varnish in the past though]

I did use that loctite. It was just a rookie mistake too much must have been put on and I didn't notice. I put loctite on all the screws and only had a problem with one.

Originally Posted by cdmorenot

Hey man. You're talking about the screw that does not show up on the other side of the link right?

In other words the end tip is hidden... Yeah, that one I managed to mangle a couple of times myself. Go to the AD and get it from them. The screw is $8 and they may have to order it.

Yep! That's the one. Thank you very much that makes me much happier to know lol.